Super racing flat silver braids (1 m)

Slot.it SISP18 Braids: Competition Performance in Every Millimetre of Contact

Braids are one of those components that go unnoticed until they fail. Poor contact results in micro-cuts, loss of traction, and inconsistent lap times. The Slot.it super racing flat silver braids (reference SISP18) are designed precisely to eliminate that weak point: ultra-thin profile, silver finish, and one metre in length so you can prepare or replenish the number of cars you need without running short on material.

Function and Performance

The ultra-thin profile of these braids allows the guide to sit freely in the slot without the thickness of the conductor interfering with the chassis geometry. This is especially relevant in cars with tighter setups, where every tenth of a millimetre in guide height can affect cornering behaviour.

The silver finish indicates a composition aimed at electrical conductivity, favouring a clean and constant current transfer from the track to the motor. The result is a more direct response to the controller and greater consistency in lap times.

Compatibility and Applications

As a replacement part from the Slot.it range, these braids are designed to fit the brand's guides, commonly found in cars running on Sport track (compatible with Scaleauto tracks, among others). However, their continuous one-metre format allows them to be cut to the exact length required for any standard guide, which expands their utility to other chassis and brands as long as the dimensions are compatible.

• One metre format: sufficient material for several renewals or to equip different cars.
• Ultra-thin profile: ideal for chassis with little tolerance between guide and car floor.
• Silver finish: high conductivity and stable contact with the track.
• Official Slot.it replacement: quality and consistency guaranteed within the brand's range.

Installation and Preparation

The replacement process is straightforward: remove the worn braids from the guide slots, cut the new braid to the necessary length with scissors or a modelling scalpel, and insert each end into its slot until it is securely fitted. Ensure that the contact with the track is uniform across the entire width of the braid before closing the chassis.

It is advisable to check the condition of the braids periodically, especially during long running sessions or on heavily used tracks, as accumulated wear is the most common cause of below-expected electrical performance.

Common Errors

• Not cutting to the correct length: a braid that is too long can bend inside the slot and lose contact at certain points on the track.
• Reusing worn braids: when the material is thinned by friction, conductivity drops significantly even if the visual contact appears correct.
• Not cleaning the guide before installation: graphite or dirt residues accumulated in the slot can prevent a proper seating of the new braid.

Frequently Asked Questions

How many cars can I equip with one metre of braid?

It depends on the size of the guide and the length required for each slot, but typically one metre of braid is enough to equip between four and six cars in 1/32 scale, with room for some adjustment or additional replacement.

Are they compatible with guides from other brands besides Slot.it?

The continuous one-metre format allows them to be cut to size, so they can be adapted to guides from other brands as long as the ultra-thin profile is compatible with the guide slot in question. We recommend checking the dimensions before installation.

How often should I change the braids?

There is no fixed rule: it depends on the intensity of use, the type of track, and the running conditions. A good practice is to check them every few sessions and replace them when visible wear, deformation, or irregular electrical response is noted.

Does the silver finish imply any difference compared to gold or other coloured braids?

The colour usually indicates the composition of the conductive material. The silver braids from Slot.it are formulated to offer high conductivity and controlled wear. For exact differences between references in the range, consult the technical specifications on the official Slot.it website or with your trusted distributor.

Can I use these braids on Scalextric or Ninco tracks?

These tracks use universal track, while Slot.it designs its products for Sport track. Use on universal track is possible if the guide you mount on your car accepts the profile of these braids, but it is not guaranteed without verifying dimensional compatibility.

Slot.it SISP18 super racing flat braid, silver finish, 1 metre length. Ultra-thin profile for low-profile guide compatibility in 1/32 scale slot car racing. Designed for Sport track systems, delivering consistent electrical contact and reliable current transfer for competitive and club racing setups. An essential maintenance part for Slot.it chassis preparation and tuning.