Standard Flat 0.35 Tinned Braid with Dispenser

Standard Flat Tinned Braid 0.35 from Sloting Plus: precision and convenience in every connection

The reference SP103151 from Sloting Plus brings together everything we need to keep our slot cars with reliable and consistent electrical contact: flat profile tinned copper, well-defined measurements, and a dispenser that makes material management comfortable and tangle-free.

Technical specifications

• Material: tinned copper
• Profile: flat (Flat)
• Thickness: 0.35 mm
• Approximate width: 3.4 mm
• Length: 2 metres per bag
• Includes: integrated dispenser

Function and performance

The braid is the element that collects current from the track and transmits it to the motor. A damaged braid, twisted or with high electrical resistance, directly translates into loss of response, stuttering, or erratic behaviour on track. The flat profile Standard Flat of 0.35 mm offers a generous and uniform contact surface, facilitating stable current flow both on recreational tracks and in club sessions where consistency matters.

Tinned copper resists oxidation better than bare copper, which prolongs the lifespan of the braid and maintains conductivity in optimal conditions for longer, even if the car spends time in the drawer.

The dispenser: a detail that makes a difference

Anyone who has tried to cut braid from a loose roll knows what it is like to struggle with the material: it tangles, bends, and gets contaminated with dust or grease. The dispenser included with this reference from Sloting Plus precisely solves that problem. It allows you to extract the right amount, keeps the rest perfectly stored and protected, and takes up little space in the toolbox or track box bag.

Installation and preparation

To install the braid correctly, it is advisable to cut the necessary length accurately before soldering. The flat profile fits well into the guide housing and facilitates routing through the chassis interior. It is recommended to clean the soldering points with flux before applying solder to ensure a clean and low-resistance joint. Once installed, check that it is neither too tight nor too loose: the braid should be able to move with the guide without pulling on the assembly.

Compatibility and applications

The Flat format of 3.4 mm wide is compatible with most slot car chassis in 1/32 and 1/24 scale that use standard guides. It is suitable for preparations in cars from brands such as NSR, Slot.it, Scaleauto, Avant Slot, or any other manufacturer that uses conventional flat braid housings. Always check the chassis specifications to confirm the maximum allowable width.

Frequently asked questions

What is the difference between Flat braid and round braid?

The Flat braid has a flat profile that offers a larger contact surface with the track and fits better into the housings designed for this type. The round braid has a circular section and is usually used in specific applications or chassis that require it. For most standard slot cars, the flat version is the most common.

Is 2 metres enough for several cars?

Yes. The amount of braid needed per car is very small—generally a few centimetres per side—so with 2 metres we have more than enough material to prepare, repair, or replace the braids of several cars and keep a reserve for the workshop.

Does the thickness of 0.35 mm affect performance?

The thickness influences flexibility and conductivity. A thickness of 0.35 mm offers a good balance between sufficient rigidity to maintain firm contact with the track and flexibility to not interfere with the movement of the guide. It is a widely used measurement in club-level preparations.

How do I know when it is necessary to change the braid?

The most common symptoms are loss of response when accelerating, stuttering, or intermittent power cuts that cannot be explained by the condition of the track. If worn, flattened, or corroded areas are visible upon inspecting the braid, it is time to replace it.

Is it necessary to use flux when soldering the braid?

It is not strictly mandatory, but it is highly recommended. Flux cleans the metal surface at the time of soldering and promotes a joint with lower electrical resistance, resulting in a more efficient and durable connection.

The Sloting Plus SP103151 Standard Flat tinned copper braid (0.35 mm thick, approx. 3.4 mm wide, 2 m length) is a reliable choice for slot car preparation and maintenance. Compatible with most 1/32 and 1/24 slot car chassis using standard flat braid guides, it delivers stable electrical contact and long-lasting performance. The included dispenser keeps the braid tidy and ready to use, making it a practical addition to any slot car workshop or club pit box.