Zero Grip Rubber Tyre 16x8.8mm. Low Profile

The front axle that doesn't fight: Scaleauto's Zero Grip philosophy applied to the millimetre.

When preparing a slot car for competition, attention often focuses on the rear end: motor, crown gear, pinion, traction tyres… But the front axle plays an equally decisive role. If the front tyres offer too much grip, the front of the car "digs in" during corners, causing that erratic behaviour that enthusiasts know well: the car goes straight, spins out, or hinders the guide's function. The Scaleauto Zero Grip SC-4724 tyres tackle this problem at its root.

Function and performance

The Zero Grip compound is specifically formulated for the front axle. Its surface offers minimal resistance to lateral sliding, allowing the front of the car to follow the trajectory set by the guide without opposing it. The result is cleaner steering, smoother cornering, and a much more predictable driving feel, especially on tracks with tight corners or fast chicanes.

The low profile design is not just an aesthetic detail: it lowers the overall centre of gravity, keeps the front close to the track, and reduces the risk of the guide losing contact with the rail during acceleration or changes in elevation. With a diameter of 16.0 mm and 8.8 mm wide, they fit into the typical space of the front end of cars in 1/32 and 1/24 scale without compromising the chassis geometry.

Compatibility

Scaleauto indicates that these tyres are compatible with standard front rims ranging from 15.9 mm to 16.5 mm, the most common range in 1/32 and 1/24 scale slot cars. Before mounting, it is advisable to check the exact diameter of the car's rim to ensure a precise fit without play.

Mounting and preparation

Mounting does not require special tools. However, if you seek maximum performance, we recommend slightly truing the tyres after mounting to ensure perfect roundness. Scaleauto works with high consistency rubbers that minimise deformation, but a small touch-up with a lathe always makes a difference in serious competition. There is no need to apply any chemical treatment to reduce grip: the compound is already Zero Grip from the factory.

Ideal for…

• Club racers looking for more stable and predictable on-track behaviour.
• Competition setups in 1/32 and 1/24 scale where regulations allow modification of the front tyres.
• Cars prone to "bucking" or going straight in tight corners.
• Any chassis where the front end generates too much lateral friction.

Aspects to consider

These tyres are designed exclusively for the front axle. Mounting them on the rear axle would eliminate all traction and make the car uncontrollable. The pack includes 2 units, sufficient to equip a single front axle.

Frequently asked questions

What is the difference between a Zero Grip tyre and a conventional front tyre?

A conventional front tyre has a certain coefficient of grip, which can generate lateral resistance in corners and hinder the front's turn. The Zero Grip compound is formulated to slide with minimal friction, allowing the guide to be the only element that sets the trajectory.

Is it compatible with my 1/32 scale car?

Scaleauto indicates compatibility with front rims from 15.9 mm to 16.5 mm in diameter, which is the standard range for most 1/32 and 1/24 slot cars. Check the diameter of your rim before placing your order.

Do I need to true the tyres after mounting them?

It is not mandatory, but it is highly recommended in competition. A slight touch-up on a lathe after mounting ensures perfect roundness and eliminates any small eccentricity that could cause vibration at high speeds.

Can I use them on the rear axle to reduce traction on very grippy tracks?

No. These tyres are designed for the front axle. Mounting them on the rear would completely eliminate traction and make the car unmanageable. For adjusting rear traction, there are other specific compounds from Scaleauto.

How many units are included in the pack?

The SC-4724 pack includes 2 units, the necessary amount to equip the complete front axle of a car.

Scaleauto SC-4724 Zero Grip low profile front tyres, 16x8.8mm, specially formulated for slot car front axles in 1/32 and 1/24 scale. The no-grip rubber compound eliminates lateral friction, allowing the guide to steer freely and improving overall handling in tight corners. Compatible with standard front rims from 15.9mm to 16.5mm. Pack of 2 units. A trusted choice among club racers and competitive slot car builders looking for consistent, predictable front-end behaviour.